Tel: +86-18638759011 E-mailem:inquiry@rsnewrefractory.com

O Kontakt |

Energetický průmysl

The working environment of CFB boiler is high speed fluidized particles abrasion and impact, chemical reaction and corrosion, frequent thermal exchange. So CFB boiler lining refractory have high mechanical strength, excellent abrasion resistance, dobrá odolnost proti korozi, good thermal shock resistance and so on.

Energetický průmysl
Energetický průmysl

Refractories Conformation Scheme for CFB Boiler

Refractories for CFB Boiler System

Energetický průmysl
  • Boiler Combustion Chamber

RSNM-B Castables(Dense phase zone, sparse phase zone, boiler roof and etc.)RSNMKS Plastic Castables(Fluidized section of dense phase zone)

  • Air Separation

RSNM-A Castables or RSNM-75 Wear-resistant Bricks(Used on straight part and cone-shaped part of cyclone tube , gateway, refeeder etc.)

  • Economizer

RSZGN-42 Refractory Bricks
RSNM-75 Wear-resistant Bricks
RSNM-A Dense Castables
RSQZ -0.7 Light Weight Castables
RSQZ -0.3/0.6 Light Weight Insulating Products
RSNT-2 Castables(Beam of economizer)
RSXWT-100 Refractory Fiber Blanket

  • Ignition Air FlueCold Air Chamber

RSJZL -1 Castables
RSNT-2 Castables

  • The Tail Flue

RSNM-B Castables
RSQZBW -650/1000 Light Weight Insulating Products
RSZGN-42 Refractory Bricks

  • Unshaped Refractory Materials

Unshaped refractory is most important refractory used in CFB boiler, it accounts for 70%~80% of the total amount. Low cement castable, ultra low cement abrasion resistant castable and no cement wearing resistant castable are usually used in circulating fluidized bed boiler.

Wear-resistant Castables

The wear resistant castables, made from fused corundum, super grade bauxite, sillimanite, alumina powder and silicon powder as raw materials, are featured with convenient construction, good wear esistance,good spalling resistance, and high strength at early and mid-high temperature period, which overcome the disadvantages of traditional castables.

PoložkaSpecifikace
Objemová hustota, g/cm³110℃ ×24h≥2.75
Permanent Linear Change On Heating , %1100℃ ×3h±0.4
CCS , MPa110℃ ×24h≥100
1100℃ ×3h≥120
CMOR , MPa110℃ ×24h≥10
1100℃ ×3h≥18
Odolnost proti tepelným šokům,Cyklus1000℃ Water Quenching≥20
Wear-resistance Index,ccASTM C-704<6
Chemické složení , %Al2Ó3≥75
SiO2<18
Maximum Service Temperature,℃1600
Service AreaDense phase area and transition area of combustion chamber, furnace bottom, cyclone cylinder outlet mixing chamber.

Steel Fiber Reinforced Wear-resistant Castables

The castables are produced by adding some silicon carbide, mullite and steel fiber, to enhance the tensile property, strength and thermal shock resistance on the basis of the technology of optimized wear resistance castables. It is used in cutting direction entrance of cyclone separator andtarget areaon cartridge of circulating fluidized bed boiler, which are the worst wear parts.

ZnačkaRSNM-A
PoložkaSpecifikace
Objemová hustota , g/cm³110℃ ×24h≥2,8
Permanent Linear Change On Heating , %1100℃ ×3h±0.4
CCS , MPa110℃ ×24h≥100
1100℃ ×3h≥120
MOR , MPa110℃ ×24h≥17
1100℃ ×3h≥20
Odolnost proti tepelným šokům,Cyklus1000℃ Water Quenching≥25
Wear-resistance Index,ccASTM C-704≤5
Chemické složení,%Al2Ó3≥80
SiO2<11
Maximum Service Temperature,℃1600
Service AreaHorizontal flue at furnace outlet, straight part and cone-shaped part of separator ,entry and exit, refeeder and dipleg etc.

Wear-resistant Plastic Refractories

Compared with the traditional refractory plastic,the wear resistant plastic refractories are featured with good plastic ability, long shelf life,high strength and good wear resistance. The strength of the material increases with the increasing temperature due to the adoption of composite binder. The wear-resistant plastic refractories,using fused corundum,mullite and super grade bauxite as main raw materials,the addition of Guangxi white clay ensures that the refractory plastic can have high plasticity, enhance the crushing strength and wear resistance, especially suitable for repairing CFB boilers and the overall construction of wear resistant lining. Refractory plastic can be processed into non-baking materials, then furnace can be directly start if necessary.

ZnačkaRSNMKS-A
PoložkaSpecifikace
Objemová hustota , g/cm³110℃ ×24h≥2,7
CCS , MPa110℃ ×24h≥80
1100℃ ×3h≥100
MOR , MPa110℃ ×24h≥12
1100℃ ×3h≥14
Chemické složení , % Al2Ó3≥80
Maximum Service Temperature , ℃1600
Wear-resistance Index,ccASTM C-704≤6
Service AreaWear resistant parts,such as dense phase area, overheating screen, separator target area, horizontal flue etc.

Thermal Shock Resistant Castables

Most CFB furnaces are ignited under the bed, the ignition temperature is high, and the temperature rises rapidly after ignition; The oil gun will be turned off after the boiler reaches 650 stupně, and the temperature will drop to 150 degrees instantaneously. Proto, thermal shock resistant and high refractoriness are required, especially in the air chamber, igniter, and water-cooled air chamber. Thermal shock resistant castable is the best choice for these areas.

ZnačkaRSKRZ-1
PoložkaSpecifikace
Objemová hustota,g/cm³110℃ ×24h≥2,8
CCS,MPa110℃ ×24h≥100
1100℃ ×3h≥120
MOR,MPa110℃ ×24h≥17
1100℃ ×3h≥20
Odolnost proti tepelným šokům,Cyklus1000℃ Water Quenching≥25
Maximum Service Temperature,℃1600
Service AreaIgniter, ignition air flue, water cooling chamber

Fireclay Castables

ZnačkaRSNTJ-2
PoložkaSpecifikace
Objemová hustota,g/cm³110℃ ×24h2.2-2.4
CCS,MPa110℃ ×24h≥40
1100℃ ×3h≥50
MOR,MPa110℃ ×24h≥5
1100℃ ×3h≥6
Odolnost proti tepelným šokům,Cyklus1000℃ Water Quenching≥20
Maximum Service Temperature,℃1400
Service AreaIgnition duct, mixing chamber, coal economizer beam

Získejte cenovou nabídku

    Zanechat vzkaz